Jyväskylä University - Device Booking System

Key facts

Status

Unavailable

Location

YE 419

Room

YE419

Is resource specific training required?

Yes

Minimum reservation length

1 h

Maximum reservation length

8 h

Reservation change/cancellation limit

24 h

Administrator contact info

Name	Email	Phone
Antti Tiihonen	antti.j.tiihonen@jyu.fi	+358505213380
Ari Väisänen	ari.o.vaisanen@jyu.fi	+358408053719
Siiri Perämäki	siiri.e.peramaki@jyu.fi	+358408053495
Kaisa Lampinen	kaisa.m.lampinen@jyu.fi	+358406528384

Pricing

JYU Chemistry and related groups: free of charge
JYU Internal: collaboration required
Commercial use: contact ari.o.vaisanen@jyu.fi or kaisa.m.lampinen@jyu.fi for a quotation

Resource information

Manufacturer

PerkinElmer

Model

Nexion 350D

Properties

Instrument installation requirements:

Physical size (instrument) WxDxH 123x75x76 cm, 190 kg
Floor space (instrument and Prepfast autosampler) WxD 210x110 cm
Physical size (roughing pump) WxDxH 40x30x30 cm, 20 kg
Vacuum roughing pump distance max. 2 m from the instrument, can be placed under instrument table
Physical size (chiller) WxDxH 50x75x70 cm, 90 kg
Floor space (chiller) WxD 80x110 cm
Room temperature 20 ± 2 °C, humidity 35–50 %
Heat dissipation 2,3 kW instrument + 1,5 kW pump + 3 kW chiller
Exhaust fume temperature up to 100 °C, duct temperature spec 70 °C
Fume extraction capacity min. 9 m³/min, flexible duct 2x 100 mm
Instrument argon, quality ≥ 99,996 % / 4.6
Instrument ammonia (cylinder), quality ≥ 99,999 % / 5.0
Instrument helium (cylinder), quality ≥ 99,9999 % / 6.0
Liquid argon is recommended
Available argon pressure at the regulator should be between 5,5–8,3 bar, connector ¼" Swagelok
Argon consumption is approximately 20 L/min, weekly consumption is approximately 10 m³ if the instrument is running 8 h each workday, and 160 L argon tank lasts for approx. 3 months
Ammonia consumption is approx. 0,6 mL/min @ 0,5 bar, small 60 L cylinder lasts for long
Helium consumption is approx. 5 mL/min @ 2,8 bar
Reaction cell gases should be stored in their own ventilated cabinet with direct transfer lines connected to the instrument
Electrical connection requirement for the instrument (2,5 m cord, IEC 60309 32 A plug "blue, three prongs"): single phase 200-240 V (± 10 %), 50/60 Hz (± 1 %), dedicated 32 A fuse, power 3720 VA
Connection for the pump, Schuko: single phase 200-240 V (± 10 %), 12 A, 50/60 Hz (± 1 %), dedicated 16 A fuse, power 1500 VA
Connection for the chiller unit, Schuko: single phase 230 V, 10 A, 50 Hz, dedicated 16 A fuse, cooling capacity 2100 W @ 25 °C, water circulation 13 L/min, requires proprietary heat transfer fluid, power 2300 VA
GFCI device should not be installed (high earth leakage current)
Computed desk, computer, monitor and their regular electrical connectivity (normal IT equipment)
Communications via USB and Ethernet, no internet connection needed, Windows 10

Physical size (instrument) WxDxH 123x75x76 cm, 190 kg
Floor space (instrument and Prepfast autosampler) WxD 210x110 cm
Physical size (roughing pump) WxDxH 40x30x30 cm, 20 kg
Vacuum roughing pump distance max. 2 m from the instrument, can be placed under instrument table
Physical size (chiller) WxDxH 50x75x70 cm, 90 kg
Floor space (chiller) WxD 80x110 cm
Room temperature 20 ± 2 °C, humidity 35–50 %
Heat dissipation 2,3 kW instrument + 1,5 kW pump + 3 kW chiller
Exhaust fume temperature up to 100 °C, duct temperature spec 70 °C
Fume extraction capacity min. 9 m³/min, flexible duct 2x 100 mm
Instrument argon, quality ≥ 99,996 % / 4.6
Instrument ammonia (cylinder), quality ≥ 99,999 % / 5.0
Instrument helium (cylinder), quality ≥ 99,9999 % / 6.0
Liquid argon is recommended
Available argon pressure at the regulator should be between 5,5–8,3 bar, connector ¼" Swagelok
Argon consumption is approximately 20 L/min, weekly consumption is approximately 10 m³ if the instrument is running 8 h each workday, and 160 L argon tank lasts for approx. 3 months
Ammonia consumption is approx. 0,6 mL/min @ 0,5 bar, small 60 L cylinder lasts for long
Helium consumption is approx. 5 mL/min @ 2,8 bar
Reaction cell gases should be stored in their own ventilated cabinet with direct transfer lines connected to the instrument
Electrical connection requirement for the instrument (2,5 m cord, IEC 60309 32 A plug "blue, three prongs"): single phase 200-240 V (± 10 %), 50/60 Hz (± 1 %), dedicated 32 A fuse, power 3720 VA
Connection for the pump, Schuko: single phase 200-240 V (± 10 %), 12 A, 50/60 Hz (± 1 %), dedicated 16 A fuse, power 1500 VA
Connection for the chiller unit, Schuko: single phase 230 V, 10 A, 50 Hz, dedicated 16 A fuse, cooling capacity 2100 W @ 25 °C, water circulation 13 L/min, requires proprietary heat transfer fluid, power 2300 VA
GFCI device should not be installed (high earth leakage current)
Computed desk, computer, monitor and their regular electrical connectivity (normal IT equipment)

Communications via USB and Ethernet, no internet connection needed, Windows 10

Image(s)

Host unit

Kemian laitos

Contact information

Name	Email	Phone
Siiri Perämäki	siiri.e.peramaki@jyu.fi	+358408053495
Kaisa Lampinen	kaisa.m.lampinen@jyu.fi	+358406528384
Ari Väisänen	ari.o.vaisanen@jyu.fi	+358408053719

Capacity

Additional information

Attachments

Organization

MOTD

Laite on varattavissa kalenterin mukaisesti vasta kun uusi vakuumipumppu on asennettu.

The instrument can be reserved according to the calendar only after the new vacuum pump is installed.

Concise description

Inductively coupled plasma - mass spectrometer PerkinElmer Nexion 350D

PerkinElmer Nexion 350D ICP-MS