Jyväskylä University - Device Booking System

Key facts

Status

Available

Location

YE 403

Room

YE403

Is resource specific training required?

Yes

Minimum reservation length

1 h

Maximum reservation length

8 h

Reservation change/cancellation limit

24 h

Administrator contact info

Name	Email	Phone
Antti Tiihonen	antti.j.tiihonen@jyu.fi	+358505213380
Ari Väisänen	ari.o.vaisanen@jyu.fi	+358408053719
Siiri Perämäki	siiri.e.peramaki@jyu.fi	+358408053495
Kaisa Lampinen	kaisa.m.lampinen@jyu.fi	+358406528384

Pricing

JYU Chemistry and related groups: free of charge
JYU Internal: collaboration required
Commercial use: contact ari.o.vaisanen@jyu.fi or kaisa.m.lampinen@jyu.fi for a quotation

Resource information

Manufacturer

PerkinElmer

Model

Avio 500

Description

Moodle course

Properties

Instrument installation requirements:

Physical size (instrument) WxDxH 76x84x87 cm, 165 kg
Floor space (instrument and autosampler) WxD 160x130 cm
Physical size (chiller) WxDxH 40x70x60 cm, 80 kg
Floor space (chiller) WxD 70x100 cm
Room temperature 20 ± 2 °C, humidity 20–80 %
Heat dissipation 2,2 kW instrument + 3 kW chiller
Exhaust fume temperature up to 200 °C
Fume extraction capacity min. 4 m³/min, flexible duct 100 mm
Instrument argon, quality ≥ 99,996 % / 4.6
Instrument nitrogen, quality ≥ 99,999 % / 5.0
Liquid argon is recommended
Suitable optics purge gases are argon or nitrogen (N₂ is cheaper), required flow rate 1,5 L/min (low purge, N₂) and 8.0 L/min (high purge, N₂) or argon respectively 1,4 L/min (low purge) and 7,0 L/min (high purge) @ 3,5 bar
Available argon pressure at the regulator should be between 5,5–8,25 bar, connector ¼" Swagelok
Argon consumption while plasma on is approximately 10 L/min and in standby/idle 2 L/min, therefore consumption in a week is approximately 40 m³ if the instrument is running 8 h each workday and is on standby during nights and weekends (shutdown during weekend saves approx. 6 m³), and 160 L argon tank lasts for 3-4 weeks
If nitrogen is used, regulator pressure should be between 2,8–8,3 bar
Pressurized air (cooling and shear gas) should be clean, dry and oil-free with consumption of 25 L/min @ min. 5,5 bar, ¼" Swagelok (also nitrogen with same requirements can be used)
Electrical connection requirement for the instrument (2,5 m cord, IEC 309 16 A plug "blue, three prongs"): single phase 200-254 V, 50/60 Hz (± 1 %), dedicated 16 A fuse, power 2800 VA
Electrical requirements for the chiller unit (2 m cord, Schuko): single phase 230–240 V, 12 A, 50 Hz, dedicated 16 A fuse, cooling capacity 2000 W @ 20 °C, water circulation 4 gal/min @ 55 psi, requires Polyscience Whispercool heat transfer fluid
GFCI device should not be installed (high earth leakage current)
Computer desk, computer, monitor and their regular electrical connectivity (normal IT equipment)
Communications via USB and Ethernet, no internet connection needed, Windows 10

Image(s)

Host unit

Kemian laitos

Contact information

Name	Email	Phone
Siiri Perämäki	siiri.e.peramaki@jyu.fi	+358408053495
Kaisa Lampinen	kaisa.m.lampinen@jyu.fi	+358406528384
Antti Tiihonen	antti.j.tiihonen@jyu.fi	+358505213380
Ari Väisänen	ari.o.vaisanen@jyu.fi	+358408053719

Capacity

Organization

MOTD

HUOM! Laitteella havaittu jälleen nebulisaatiokaasun virtausongelmia. 0,6 virtausnopeus vaatii käsisäädön n. 0,72 arvoon. Plasma käyttäytyy normaalisti. Vikaa ja ratkaisua selvitetään.

NOTE! Nebulization gas flow problem has resurfaced. Regular flow of 0,6 can be attained by adjusting it manually to approx. 0,72 setpoint value. Plasma appears to work without issues. Problem cause and solution are currently being investigated.

Concise description

Inductively coupled plasma - optical emission spectrometer PerkinElmer Avio 500

PerkinElmer Avio 500 ICP-OES